Automation solutions in secondary packaging

Cartoning for secondary packaging

Before the cartoning of the primary packaging, a main application in secondary packaging, the conveyor logistics needed for transport in and out must also be safeguarded. Dynamic, efficient and flexible solutions for safe automation are required in order to be competitive.

At the exact moment when covers and flaps on plants must be opened, there are other flaps that should be protected, to avoid contact with high temperatures, for example, such as those that occur while stretch shrink wrapping. Product connectivity and a flexible series connection of safety sensors and control technology not only enable maximum safety for operators, but also ensure the efficiency of the packaging machine.

We offer safe automation solutions for secondary packaging, whether it's a question of safety sensors, safe small controllers or operating mode selector switches. You can rely on our high level of customer orientation and specialist knowledge of the standards. We're happy to support you with your requirements.

Increase safety on carton erector

With optical detection on the carton magazine or carton infeed on carton erectors, the TÜV SÜD-certified solution for PL d / SIL  2 prevents an operator from reaching into the machine through the empty material infeed opening and injuring themself. While there is sufficient packaging in the magazine, the opening is covered and it is impossible to reach into the danger zone while the packaging plant is running. As a result, the packaging acts as natural protection and secures the movable guard. If the number of cartons in the magazine reaches or falls below the defined minimum, this will be detected by two optical sensors, which shut down the outputs via the safe small controller PNOZmulti 2 or the modular safety relays myPNOZ. The machine is in stop mode until packaging is again in place.

The combination of optical sensors and safety controller gives companies in the packaging industry an automated solution when it comes to safely monitoring the carton infeed. If the safety circuit is to be created using configuration software, you automate using PNOZmulti 2. The modular safety relays myPNOZ are configured via the hardware sequence. We'll be happy to advise you on the right solution for you.

Your benefits:

  • Higher productivity when packaging, plus cost saving: packaging provides natural protection; no need for fences or similar
  • Greater safety for personnel: minimised accident risk through the use of safe control technology in conjunction with optical sensors, approved by TÜV-SÜD
  • Easy to integrate into existing packaging plants; retrofit possible.
  • Minimum space requirement due to compact sensor housing and individual installation options to the side of or above the carton magazine
  • Formats can be changed efficiently
  • Covers applications for packaging machines in accordance with EN 415

Application examples:

Example application: solution prevents accident risk
  • The TÜV-SÜD-certified solution for PL d / SIL 2: greater safety for personnel, minimised accident risk.
Example application: no hazard on the machine
  • Sufficient cartons in the magazine: no danger!
Example application: machine in stop
  • The machine is in stop mode until sufficient cartons are again in place.

Solution with the safe small controller PNOZmulti 2 and optical sensors

  • Flexibility: all base units PNOZmulti 2 can be used and are certified
  • One-stop shop: all other application-related safety functions can be monitored alongside (E-STOP, safety gates etc.)
  • Production: Integrated diagnostics via PVIS, with plain text messages for quick resolution of downtimes with clear instructions
  • Cost-optimised: Possible to monitor two carton magazines with just one base unit: one function block is configured and 2 sensors are needed per magazine

More about optical sensors

Safe monitoring on carton magazine TÜV-SÜD-certified for PL d/SIL 2

Solution with modular safety relay myPNOZ and optical sensors

Safety on carton erector TÜV-SÜD-certified for PL d / SIL 2
  • Pre-configured: creator type code myPNOZ.91.CKA360AB000XB700
  • Plug & play: in conjunction with the sensors, easy to wire - ready to use instantly
  • Simple: diagnostics via LEDs
  • Flexible: possible to monitor additional safety functions (creator type code must remain as certified, but can be customised (see documentation for details)

More about optical sensors

Rapid fault detection and high plant availability

Intelligent, networked production processes can significantly increase the productivity of your packaging machine. However, this is only possible if a wide variety of data is automatically available. With our diagnostic solution Safety Device Diagnostics, you can record diagnostic data such as individual serial numbers, version status, current states and error states. Fastest possible fault detection ensures short downtimes.

You can then use your diagnostic data for predictive maintenance, when stretch shrink wrapping for example.

Application: film shrink wrapper

Safety for the robot cell

Safeguarding a robot cell

The I/O module PDP67 PN with Profinet/Profisafe interface ensures safety where there is no room for a control cabinet, in a robot cell for example. Thanks to the IP67 protection type and robust zinc housing, it is ideal for use outside of the control cabinet. Even in temperatures from -30°C to 70°C, it reliably passes the sensor and actuator data to the higher level controller!

As a result, the robot is guaranteed to go to a safe state as soon as your employee gains access to the machine.

More information about packaging technology

Contact

Pilz New Zealand
4 Prescott Street, Penrose
Auckland 1061
New Zealand

Telephone: +64 9 6345350
E-Mail: office@pilz.co.nz

Pilz New Zealand

Telephone: +64 9 6345350
E-Mail: office@pilz.co.nz

Technical Support

Telephone: +64 9 6345350
E-Mail: office@pilz.co.nz